Celebrating Forklift Safety Day 2017

The Industrial Truck Association has announced it’s second annual Forklift Safety Day, to be held June Tuesday, June 13. There are things you can do to take advantage of this day to help create awareness about the dangers that forklifts present and how to minimize the potential for accidents that can result in injury or death, damage to your facility, equipment and financial losses. We’ve compiled a short list of things you can do on June 9th to improve safety on and around your forklifts.

  1. Make sure all your forklift operators have been trained and that their refresher training is up to date, if applicable or necessary.
  2. Take time to teach your forklift operators the importance of daily inspections of their forklifts. Daily inspections reduce the risk of equipment failure and catch small problems before they blossom into giant ones. You can download daily forklift inspection sheets for both IC forklifts and electric forklifts.
  3. Download and post our free forklift safety posters for:
    1. Pedestrian Notification
    2. Notice that Forklifts are in Operation
    3. That Only Trained Employees May Operate Forklifts
  4. Take some time to gather any staff that operates around forklifts, but not on them, to refresh them about the dangers of this equipment and how to be sure to use safe procedures when they are in an area of your facility where forklifts are being operated.
  5. Make sure all your forklift’s maintenance is up to date. If you have a Planned Maintenance Agreement, this would be a good time to review it with your service provider to ensure all standard checkpoints as well as unique equipment attachments are being inspected and maintained properly.
  6. Review any unique “site specific” features your facility may have and be sure your operators are aware of proper handling of equipment while on or around these features (ramps, areas where floors can be slick, floor substrates that vary etc…)
  7. Make sure that training is part of your company’s orientation for anyone that will or MIGHT operate a forklift. Remember, employees that have not been properly trained aren’t even allowed to sit on and start a forklift, much less move it out of the way of anything.
  8. Make sure you forklifts have proper safety equipment and that it’s operating properly. Lights, horns, back-up alarms, seat belts, fire extinguishers etc… Improve pedestrian safety, check out our Blue Spot Safety Light by Linde.
  9. Make sure you have lock-out kits to ensure that forklifts that do not pass an inspection are locked out immediately until repairs are made.
  10. Review all your forklifts for possible replacement. Old forklifts, or those that are getting “up there” in hours, might be potential threats. Review safety records and maintenance logs for your equipment. You might find this could be a good time to replace some or even all of your forklifts.-

Our goal is to help you operate safe, efficient and productive forklift equipment. To discuss forklift safety, operator training –or to get a quote on new equipment, please give us a call at 866-393-9833.

Advertisements

CLARK Material Handling Celebrates Forklift Safety Day

The day is here and companies all around the country are taking time today to bring awareness to the dangers presented by forklifts. We’ve been promoting what you can do to celebrate Forklift Safety Day, and today, our flagship line, CLARK Material Handling is having a celebration at their Lexington, KY headquarters. Below is a summary of the festivities.

Lexington, KY (June 3, 2016) – CLARK Material Handling Company, underscoring its commitment to the safe use of forklifts and importance of operator training, is hosting a community-wide forklift safety awareness event at its Lexington campus on Tuesday, June 14, 2016, in support of the third annual National Forklift Safety Day. The program will run from 11:30AM to 1:30PM and is open to the public. CLARK is located at 700 Enterprise Drive in Lexington, KY at the intersection of New Circle Road and Old Frankfort Pike.

A full schedule of events planned to endorse and promote National Forklift Safety Day include:

  • An open house including plant tours at 11:30AM and 12:30PM
  • Special Flag Raising Ceremony at 12:00 noon, in honor of Flag Day
  • “Lift Truck Rodeo” competition and safety demonstrations
  • A display of aftermarket safety products
  • The premiere of the new CLARK video, “Forklift Safety: Pre-Shift Inspection”
  • Local media coverage including a live radio remote by 98.1 FM ‘The Bull’, WBUL
  • Free lunch – prepared by Smokin’ Jax Grill
  • Door prizes

In addition to the activities in Lexington, CLARK executives will participate in the Industrial Truck Association (ITA) National Forklift Safety Day events taking place June 14 in Washington, D.C.

“It is vitally important to emphasize the safe use of forklifts and proper operator training,” stated Dennis Lawrence, President and CEO of CLARK. “Forklift safety is not just a one day per year focus. At CLARK, forklift safety is our top priority every day. We are proud to join with the ITA and our fellow forklift manufacturers to raise awareness about the safe use of forklifts and the continual need for operator training.”

In further support of forklift safety, CLARK is offering customer discounts on select safety products purchased during June, 2016. Additionally, CLARK is conducting a lift truck operator instructor training certification course for a number of area companies.

National Forklift Safety Day, sponsored by the Industrial Truck Association, serves as a focal point for manufacturers to highlight the safe use of forklifts and the importance of operator training. This day provides an opportunity for the industry to educate customers, policymakers and the administration on forklift operating safety practices.

Tri-Lift NC, Inc. is your source for quality new forklifts, forklift service, parts, rentals and Forklift operator training. Contact us 866-393-9833 to inquire about any of our products or services.


Celebrating Forklift Safety Day 2016

Forklift Safety Day LogoThe Industrial Truck Association has announced it’s second annual Forklift Safety Day, to be held June Tuesday, June 14. There are things you can do to take advantage of this day to help create awareness about the dangers that forklifts present and how to minimize the potential for accidents that can result in injury or death, damage to your facility, equipment and financial losses. We’ve compiled a short list of things you can do on June 9th to improve safety on and around your forklifts.

  1. Make sure all your forklift operators have been trained and that their refresher training is up to date, if applicable or necessary.
  2. Take time to teach your forklift operators the importance of daily inspections of their forklifts. Daily inspections reduce the risk of equipment failure and catch small problems before they blossom into giant ones. You can download daily forklift inspection sheets for both IC forklifts and electric forklifts.
  3. Download and post our free forklift safety posters for:
    1. Pedestrian Notification
    2. Notice that Forklifts are in Operation
    3. That Only Trained Employees May Operate Forklifts
  4. Take some time to gather any staff that operates around forklifts, but not on them, to refresh them about the dangers of this equipment and how to be sure to use safe procedures when they are in an area of your facility where forklifts are being operated.
  5. Make sure all your forklift’s maintenance is up to date. If you have a Planned Maintenance Agreement, this would be a good time to review it with your service provider to ensure all standard checkpoints as well as unique equipment attachments are being inspected and maintained properly.
  6. Review any unique “site specific” features your facility may have and be sure your operators are aware of proper handling of equipment while on or around these features (ramps, areas where floors can be slick, floor substrates that vary etc…)
  7. Make sure that training is part of your company’s orientation for anyone that will or MIGHT operate a forklift. Remember, employees that have not been properly trained aren’t even allowed to sit on and start a forklift, much less move it out of the way of anything.
  8. Make sure you forklifts have proper safety equipment and that it’s operating properly. Lights, horns, back-up alarms, seat belts, fire extinguishers etc… Improve pedestrian safety, check out our Blue Spot Safety Light by Linde.
  9. Make sure you have lock-out kits to ensure that forklifts that do not pass an inspection are locked out immediately until repairs are made.
  10. Review all your forklifts for possible replacement. Old forklifts, or those that are getting “up there” in hours, might be potential threats. Review safety records and maintenance logs for your equipment. You might find this could be a good time to replace some or even all of your forklifts.-

Our goal is to help you operate safe, efficient and productive forklift equipment. To discuss forklift safety, operator training –or to get a quote on new equipment, please give us a call at 866-393-9833.


OSHA Increasing Fines for First Time in Decades

On November 3rd it was announced that OSHA would increase penalties for the first time since 1990. The new provision is entitled the “Federal Civil Penalties Inflation Adjustment Act Improvements Act of 2015.”

This law compensates for the “freeze” on financial penalty increases that had been in place for the last 25 years. The Agreement allows OSHA to make a one-time “catch-up” increase to compensate for the more than two decades of no increases. The catch-up increase can’t exceed the inflation rate from 1990 through 2015 as measured by the Consumer Price Index (CPI), which will be about 82%.

Assuming OSHA applies the maximum catch-up increase allowed, the current maximum $70,000 fine for a Repeat and Willful violation would grow to as much as $125,000 each. The new act does include a potential exception to the increases. OSHA is allowed to forego following the  guidelines if “increasing the civil monetary penalty by the otherwise required amount will have a negative economic impact [on America]” or “the social costs of increasing the civil monetary penalty by the otherwise required amount outweigh the benefits.” This language gives OSHA considerable latitude to apply these fines as they see fit. After this one-time catch-up increase, OSHA will use inflation rate as a guide for future increases.

Employers may have several months to anticipate these higher penalties, but action on safety should begin immediately. Ensuring your forklift fleet is being properly maintained by service professionals and that all your forklift operators have current training on the equipment they operate, in the facility they operate them in, will keep you protected from these fines.

As we have discussed in previous articles forklift operator training and forklift maintenance have benefits that go beyond avoiding expensive penalties.  Workplace safety protects workers, improves morale and can actually help the bottom line profits for all workplaces. Rather than just treating safety as an expense, management should work to develop a business plan to achieve safety goals, avoid fines, and reduce insurance expense and lost time.

Visit our Forklift Operator Training page and learn more about our Planned Maintenance Program to ensure your fleet, and operators are safe and productive. Then contact us at 866-393-9833 for a quote to proving ongoing training and maintenance to ensure they both stay within safe operating parameters.


OSHA’s 2015 Top Ten Citations Announced

osha logoThe Occupational Safety and Health Administration (OSHA) announced the preliminary Top 10 most frequently cited workplace safety violations for fiscal year 2015. Patrick Kapust, deputy director of OSHA’s Directorate of Enforcement Programs, presented the Top 10 on the Expo floor as part of the 2015 NSC Congress & Expo, the world’s largest gathering of safety professionals.

“In injury prevention, we go where the data tell us to go,” said National Safety Council President and CEO Deborah A.P. Hersman. “The OSHA Top 10 list is a roadmap that identifies the hazards you want to avoid on the journey to safety excellence.”

The Top 10 for FY 2015* are:

  1. Fall Protection (1926.501) – 6,721
  2. Hazard Communication (1910.1200) – 5,192
  3. Scaffolding (1926.451) – 4,295
  4. Respiratory Protection (1910.134) – 3,305
  5. Lockout/Tagout (1910.147) – 3,002
  6. Powered Industrial Trucks (1910.178) – 2,760
  7. Ladders (1926.1053) – 2,489
  8. Electrical – Wiring Methods (1910.305) – 2,404
  9. Machine Guarding (1910.212) – 2,295
  10. Electrical – General Requirements (1910.303) – 1,973

As you can see, forklifts and lift equipment is high on OSHA’s lists of citations. One way to avoid citations pertaining to your forklift fleet is to ensure you’re following OSHA’s regulations regarding powered industrial trucks (lift trucks), that your fleet is being properly and regularly maintained and that your forklift operators have received adequate training, and that the training is up-to-date.

If you’re unsure of your fleet’s condition or your operator’s training status, contact us at 866-393-9833 and we will help you ensure you do not end up on OSHA’s list of citations!


Five Things You Can do to Prevent Workplace Violence

Violence in the workplace often erupts without warning, and can have tragic results. Taking steps to prevent these situations can improve safety in your workplace, improve employee satisfaction and lead to increased productivity. Conversely, ignoring potential hazards can result in employee injury, even death — and legal action at considerable costs to the company.

OSHA has outlined five steps you can take to identify and prevent these violent encounters before they happen. While they are not directly related to materials handling operations, we feel these guidelines can apply to a wide variety of organizations, including your company.

Management Commitment and Employee Participation

As with any initiative, without the commitment of management and leadership, the rank-and-file of the organization will likely ignore any efforts to improve safety with regards to violence. Company leadership must be involved on a regular basis and visibly endorse the effort. This can be achieved by establishing a safety and health committee, and having leadership rotate in and out of meetings conducted by the committee.

Management must articulate a policy and establish goals for the company. Once a plan has been developed, leadership should allocate sufficient resources to accomplish the goals and uphold program performance expectations. Providing resources could entail meetings with health professionals to help identify potential hazards, creating visible signage and using other communication methods to keep workers involved in and aware of the program.

Worksite Analysis and Hazard Identification

There are probably facets of your operation that are prone to producing higher anxiety or tension among your employees. These could be actual physical conditions such as heat, cold, and hazardous areas as well as departments that demand high productivity, or even interaction with the public. Taking stock of these areas and identifying factors that are the least or most likely to create a stressful atmosphere are key to prevention.  Two steps you can take to identify and prevent violence include:

  • Conducting job hazard analysis – Management can conduct surveys of their departments to assess the potential risk of violence among employees. This not only includes internal assessments, but assessments of destinations to which your employees may travel, including specific neighborhoods, time of day, etc. Sites that expose your employees to violent behavior are often outside the walls of your facility.
  • Conduct employee surveys – Employees will often tell you if their jobs create stressful situations for them and if they feel endangered by some of their job tasks. Conduction of reviews on a regular basis will help you identify these areas and create a plan to reduce danger.

Hazard Prevention and Control

Once management has established and articulated its commitment, and evaluations have taken place, a plan to reduce potential hazards must be implemented.  This step includes:

  • Identification and evaluation of control options for workplace hazards
  • Selection of effective and feasible controls to eliminate or reduce hazards
  • Implementation of these controls
  • Follow up to confirm these controls are being used and maintained
  • Evaluate effectiveness and improve, expand or update these controls as needed

Safety and Health Training

As with any program you want to succeed, employees must be trained in order to follow the steps outlined by the company to identify and report these risks and follow up as needed.

This training could include meetings with mental health experts to help identify signs of stress in colleagues that could lead to violence. It also can include training on how to avoid violence outside your facility by taking common-sense actions (such as parking under a street lamp), what to do if an employee feels threatened and even self-defense training. Other training topics can include:

  • The company’s workplace policy on violence prevention
  • Documentation and reporting
  • Location, operation and coverage of safety devices such as alarms
  • Ways to identify and deal with hostile situations
  • A standard response plan for violent situations

Recordkeeping and Program Evaluation

Recordkeeping includes reporting procedures, what gets reported and to whom, and how these records are kept. Keeping track of both “close calls” and actual events helps you identify patterns, areas of particular concern and even certain job functions that might be creating undue stress on employees. It can help you identify areas outside your facility that present a danger to your employees, such as areas of town they serve.

OSHA Log of Work-Related Injuries and Illnesses (OSHA Form 300) can help you organize information not only for reporting to your proper internal sources but also for reporting to OSHA if necessary. As of January 2015, all employers must report:

  • All work-related fatalities within 8 hours
  • All work-related inpatient hospitalizations, all amputations and all losses of an eye within 24 hours

Injuries sustained as a result of assault must be entered on the log if they meet OSHA’s recording criteria (CFR Part 1904, revised 2014).

Keeping track helps you improve your program, improve employee safety and ensure your employees are operating in a safe and productive work environment.

We hope this summary is helpful to you in establishing your own workplace violence prevention plan. To learn more about what you can do, download the complete “Guidelines for Preventing Workplace Violence) by OSHA, HERE. While it was prepared for healthcare and social service workers, the overall content of this guide can assist any company, big or small, in achieving a safer work environment for all.